Like the title says, I got one of my two LA-610 who doesn't compress anymore.. the action faded over a few months.
I tried to change the tubes and even exchanged the opto cell with the other LA-610 and it did no good.
So I guess a cap or a resistor failed.. I'd need some guidance...
duh hi all wilmot here: need schematic of the audiotronic 501 module.the one with the ne5524 ic,s.i have two of these and have been trying to get them working.e-male scats to email@example.com...thanks in advance wilmot.audiolabs
Asking on behalf of a fellow member on another electronics repair forum. He seems to have a bad a resistor that is some type of 1/4 resistor that is right beside the bridge rectifier. Obviously, these new types of schematics are tough to come by... However, the year of the device is 2007 and all...
Hi all ! does somebody have the Amek 9098 Dual Mic Pre schematics (AMEK 9098 DMA)
(without EQ ).
The Rack have not EQ but have a DI INPUT, I know the schematics is a little bit different.
Thanks for your help.
Please if you can mail me at this address if you have it :
I can't seem to find a schematic for the original (black face) DBX 162 stereo compressor. Any ideas on where to find one?
The dbxpro website (and pretty much all of the other sites that show up via a google search for a dbx 162 schematic) allows me to download a few pages of cursory alignment...
Strange one this-All the digital chips (4011's, counters, RAM,etc,) have the correct power going to them, yet the 7555 counter/comparator strange $*^t, dont know what it does chip, only has 3v. Should work between 5-12v. replace all electrolytics-NADA
Anyone have the schematic please
I have recently emailed a corporation company, which I will not name, and asked for a copy of the circuit schematic for a piece of equipment that I purchased from them. They emailed back and refused to send one to me because, and this is verbatim "Schematics for all of our products are...
I'm looking for schematics for a Scully 284B 8 track machine (circa 1976). These were the later model "California" Scullys and apparently differed from the earlier 280Bs. I realize this is a long shot as schematics for the California models seem to be very rare.
I have an old Groove Tubes 6TM mic with the PS1 Vacuum tube power supply. The mic end looks like the Groove Tubes EC7 cable in that it has a 7-pin connector. The power supply end looks like an 9-pin ADAT sync connector almost like a vga computer display connector. I am in need of the pin out...
I address to engineers and technical experts: please, help to find schematics of Series 40 mixers with vertical indicators (what gathered in the USA in 80, from a brand Otari). I have found all schematics - 1280, Series 20, 30&34. But Series 40 schematics is not anywhere! I thank for any help!
my dbx 386 has started giving me some horrendous noises on one channel. I've tried switching the tubes between channel 1 and 2, and the same channel still has the problem, so obviously my tubes are fine. Does anyone know where I might get a hold of some schematics so I can track down...
I am looking for a schematic for an old Neve 31105 Mic Pre. The reason is that the studio I work at has a few that are in need of repair. Our tech said he could do it if he can get a schematic. I am aware that many schematics are under copyright and so any other useful information on...
All is in the title.
I have an API rack with power supply module 500PS (the part with the power button on the front side plugged into the 11th slot on the right side). It looks like a 500 series module, but it is dedicated to supply the rack backbone.
The 500PS doesn't provide 48V phatom power...