| Author |
Message |
| Topic: Frequency Responses of Figure 8 Mics |
dpd
Replies: 6
Views: 999
|
 Forum: Microphones
Posted: Sat Jun 06, 2009 8:05 am Subject: Re: Frequency Responses of Figure 8 Mics |
Anyone have any frequency response curves of a Figure 8 mic? I believe that they should exhibit a 6 dB/octave slope, but I haven't seen any data.
Are you trying to find the on-axis frequency respons ... |
| Topic: Frequency Responses of Figure 8 Mics |
dpd
Replies: 6
Views: 999
|
Forum: Microphones
Posted: Thu Jun 04, 2009 9:39 pm Subject: Frequency Responses of Figure 8 Mics |
| Anyone have any frequency response curves of a Figure 8 mic? I believe that they should exhibit a 6 dB/octave slope, but I haven't seen any data. |
| Topic: DIY cable questions |
dpd
Replies: 12
Views: 2117
|
Forum: Pro Audio Gear
Posted: Fri Apr 10, 2009 6:01 pm Subject: DIY cable questions |
As for quad v. dual - I prefer dual in most cases. Quad is good for exactly the reason you reference, but over longer distances can actually degrade the signal.
J
Hey, Jeremy - what's your ration ... |
| Topic: Mastering for Voice Communications |
dpd
Replies: 6
Views: 1364
|
Forum: Mastering Sound Forum
Posted: Mon Mar 09, 2009 9:40 pm Subject: Mastering for Voice Communications |
| No overriding requirement to reduce the bit rate. processing will likely be done at 16 bit, but the dynamic range will probably be compressed into 8 bits or so to maximize loudness. Intelligibility ... |
| Topic: Mastering for Voice Communications |
dpd
Replies: 6
Views: 1364
|
Forum: Mastering Sound Forum
Posted: Sun Mar 08, 2009 9:30 pm Subject: Mastering for Voice Communications |
| It's for portable voice-projection. Voice in, amplified voice out; therefore, it's analog. Processing will be via DSP |
| Topic: Mastering for Voice Communications |
dpd
Replies: 6
Views: 1364
|
Forum: Mastering Sound Forum
Posted: Sun Mar 08, 2009 7:14 pm Subject: Mastering for Voice Communications |
I was wondering if any of the ME's here have ever done any work for purely voice communications (e.g. prepping a track for playing over a bandwidth-limited channel).
I am doing some work at my job ... |
| Topic: Soldering Iron Recommendation? |
dpd
Replies: 11
Views: 1595
|
Forum: Pro Audio Gear
Posted: Fri Mar 06, 2009 11:18 pm Subject: Soldering Iron Recommendation? |
More damage has been done by under-temp soldering irons than over-temp ones, IMO
Heat the joint, solder, and get off the joint. You DON'T want to sink a lot of heat into the CCA and end up lifting ... |
| Topic: Looking for new stereo power amp |
dpd
Replies: 14
Views: 3575
|
Forum: Mastering Sound Forum
Posted: Mon Mar 02, 2009 10:05 pm Subject: Looking for new stereo power amp |
| Amp #1 is ALIVE! Ran it at full power under load for a good while tonight - 154 Watts into 8 ohms. No oscillations noted, no notable waveform distortion (dang - should have run the FFT on the scope. ... |
| Topic: Frequency Analyzer...RTAS |
dpd
Replies: 8
Views: 1136
|
Forum: DAW Pro Audio
Posted: Thu Feb 19, 2009 10:27 pm Subject: Frequency Analyzer...RTAS |
Yeah. But I bought my license when Elemental Audio Systems originally released it (and I got a promotional discount.) The current RND price would have made me think twice...
got mine for $29. not ... |
| Topic: Frequency Analyzer...RTAS |
dpd
Replies: 8
Views: 1136
|
Forum: DAW Pro Audio
Posted: Thu Feb 19, 2009 10:10 pm Subject: Frequency Analyzer...RTAS |
| Inspector XL rules |
| Topic: dda -2dbu (-10/+4 ref levels) |
dpd
Replies: 27
Views: 16281
|
Forum: Pro Audio Gear
Posted: Wed Feb 18, 2009 4:32 pm Subject: dda -2dbu (-10/+4 ref levels) |
Most of this confusion could be solved if the audio industry just adopted what the rest of the world uses for a voltage reference:
1 Vrms sine wave = 0 dBV
there's just something refreshing abou ... |
| Topic: Looking for new stereo power amp |
dpd
Replies: 14
Views: 3575
|
Forum: Mastering Sound Forum
Posted: Sun Feb 01, 2009 12:27 am Subject: Looking for new stereo power amp |
Nice! Beyond my budget....
Finally got around to wiring the 1st chassis today. Got the AC and rectifier + filter caps done. Goes on the Variac tomorrow to see if it powers up OK, then take a loo ... |
| Topic: hi fi -what do you listen to music through? |
dpd
Replies: 16
Views: 1126
|
Forum: Pro Sound Chat
Posted: Sun Feb 01, 2009 12:22 am Subject: hi fi -what do you listen to music through? |
I got into the recording & mixing stuff from the audiophile side of things.... Most of my gear is pretty old.
I send my DAW out to a Benchmark DAC-1, routed to an Audio Research SP-9 MkII pream ... |
| Topic: Looking for new stereo power amp |
dpd
Replies: 14
Views: 3575
|
Forum: Mastering Sound Forum
Posted: Tue Jan 13, 2009 9:45 pm Subject: Looking for new stereo power amp |
| wow - Jeremy, that's great info. It's been so long since I've played the stereo game... I've been waiting for some teflon insulated wire from a guy; gave up last night and ordered it from a differen ... |
| Topic: Are Anti-Aliasing Filters always analog? |
dpd
Replies: 5
Views: 628
|
Forum: DAW Pro Audio
Posted: Tue Jan 13, 2009 9:31 pm Subject: Are Anti-Aliasing Filters always analog? |
I guess I would state it this way:
If converting from analog to digital, the AAF MUST be analog
In between digital processing signal processing stages, AAF will be digital |
| |
